Make a Cookie Tin Waterer Heater. Under $10, & 10 minutes!

You can make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes.
Winter brings many challenges for the backyard chicken-keeper, and frozen water is chief among them.  You can make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes!

Make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes!We had record-breaking, sub-zero temperatures for long periods of time in 2010 here in Connectictut and my waterers never iced over the way they used to without these heaters.  It doesn’t seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

It doesn't seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!

Supplies:

  • 10″, metal cookie tin (available at most dollar & thrift stores & likely in your garage or basement)
  • lamp assembly kit (available oniline, at hardware & home improvement stores OR buy a thrift store/tag sale lamp and take it apart)0
  • 40 watt, incandescent light bulb (in deep-freeze conditions, use a 60 watt bulb)(in light of the government phase-out, some users recommend 40 watt candelabra bulbs or CFL bulbs, but I have not, so I cannot vouch for their effectiveness)
  • Drill with 3/8″ drill bit
Lamp assembly parts.
Lamp assembly parts

INSTRUCTIONS:

1. Drill a hole in the side of the cookie tin.
2. String the pre-threaded lamp stem assembly through the hole & tighten the screw on the stem.
3. Screw in the light bulb. Voila!String the pre-threaded lamp stem assembly through the hole & tighten the screw on the stem.Screw in the light bulb.

TO USE:

Put the top on the cookie tin and place the tin on a cinder block or another level surface in the chicken run.  Plug into a GFI outlet. Place metal or plastic waterer on top of the water heater when freezing temperatures are anticipated. Disconnect when not in use or use a ThermoCube to turn the unit on when temperatures reache 35°F.

You can make your own waterer heater for use with either metal or plastic waterers. It will cost less than $10, cost pennies to run and you can complete the project in under ten minutes.
It doesn't seem as though a humble, 40 watt lightbulb should be able to produce enough warmth to keep the water in a plastic waterer from icing over, but remarkably, it does!When I made my first cookie tin water heater, I found it difficult to believe that this device, which barely felt warm to the touch, could possibly do the intended job. I was only convinced the first frigid morning I went out into the run and found no ice ring to chip out of the waterer. You may have to try it to believe it too.

Order your copy of my bestselling book,

The Chicken Chick’s Guide to Backyard Chickens!

Available now on Amazon!

Comments

avatar
Susan
Guest

What is the best kind of chicken waterers? My girls are 8 weeks old, and we plan to be gone for a couple of days in the summer so want something that holds enough water and food while we are away for two straight days.

Indygowolf
Guest

Awesome idea since heated waterers are so expensive! thanks so much for this!

Sarah M
Guest

This heater is a lifesaver! Couldn't find a tin the right size though and fastened a pizza pan to a metal dog bowl with screws! Still around $10. Getting arctic in WI. 40w bulb didn't cut if for us, 75 or 100 keeps water from freezing through any temps here!

1 52 53 54